Measuring for and hanging curtains is easy in many situations and might be executed by anybody competent in DIY (do-it-your self).
Nevertheless, there are some situations the place it is advisable to employ an expert. These embody:
* Bay windows
* Slot home windows; very slim, tall home windows
* Windows with out enough wall house above the window for a pole/observe
* Windows with out wall space or on both facet
* Non-rectangular home windows (e.g. circular, triangular,)
But for many conditions you can be using both a curtain track or pole throughout a flat rectangular window. So there are solely measurements of importance. When measuring use a sturdy metal tape measure, have a spirit level useful to check whether or not poles, batten, flooring and many others are truly level. Use correct protected steps if you're working at top and for big home windows have an assistant maintain the other finish of the tape. The old adage "measure twice and lower as soon as" holds true!
Measuring curtain width
Begin by measuring the width of the window horizontally throughout the recess occupied by the window & its frame. [Note the width of a window is just not the width of the glazing.] Now add 20-30cm (8-12"), on each side because the track or pole ought to lengthen beyond each side of the window to enable the curtains to be drawn nicely back. A large window has extra material in the curtain and so needs extra space both facet to drag back completely. If there is insufficient house on both aspect of the window you might have to regulate your design and it could be better to get some skilled assistance.
Chances are you'll discover a pre-current picket batten above the window and this could equally prolong past the window aperture. If it doesn't chances are you'll take into account replacing or extending the batten. In case you are becoming a track then the batten can be useful, whereas in case you are fitting a pole the batten may be an obstruction. While you purchase a pole make sure that the pole size (distance between finials) is the same as or larger than the required width and ensure that you may minimize the pole length down to the desired size.
Measuring curtain drop
Curtain drop is the space between the top and bottom of the material in the finished curtain, and it is determined by the model of curtain heading, positioning of the pole or monitor and the position of the bottom of the curtain. When putting in a curtain pole goal to position it above the window in order that the top of the curtain cloth is at least 10cm / 4inches above the top of the window recess.
* Curtain Poles with rings: As a rule the top of the curtain must be just below the rings so measure the drop from the underside of the ring.
* Curtain pole with eyelet curtains: In this state of affairs there are not any curtain rings and the highest of the curtain shall be above the pole. Measure the drop from the top of the pole and add 3.5cm to aloe for the amount of curtain that will likely be above the pole.
* Curtain poles with tab prime curtains measure drop from the highest of the pole.
For all curtains it's essential to determine the place the bottom will end:
* Sill size: the curtain should end 1cm above the sill (but notice that this will let extra mild into the room).
* Beneath sill length; often curtains end half method between the sill and a wall mounted radiator. Sometimes they hang over the radiator however this channels heat air up behind the scenes and so doesn't help preserve the room warm. Determine the place you need the material to end.
* Full length; the curtain finishes 1.5cm above the floor. This measurement wants precision as a result of many floors are usually not completely level. Measure the drop from an put in pole or observe in three places, the centre and to the left & right. Work with the smallest measurement however double test that the monitor or pole is level. If doubtful check the slope of the floor.
* Pooled; compared with full size curtains these normally have an additional 30cm /12 inches of cloth to pool onto the ground
Lastly
Once you have width and drop give these figures to your curtain maker who will be capable to calculate the quantity of cloth you will have and the price of making up the curtains. Additionally, you will need to agree on the curtain heading and on the type of lining for your curtains. All this may seem onerous work however you'll end up with bespoke made to measure curtains that fit your window completely; something that manufacturing facility made curtains rarely can achieve.
Author Resource:
To learn more about high quality floral shower curtains , visit our website at http://curtainsforthehome.org
![[Valid RSS feed]](http://www.look4articles.com/images/icon_Rss.png "XML Feed For RSS"){kind=icon}
Category Rss Feed
Print This Article
Add To Favorites
![[Valid RSS feed]](http://www.look4articles.com/images/rss.jpg "XML Feed For RSS")